ГлавнаяО насКонтактыДоставкаСервис

8 (495) 233 06 55

Skype Me™!

ПОКУПАЕМ ДОРОГО

ОРИГИНАЛЬНЫЕ ЗАПЧАСТИ

Hewlett Packard

 

ICQ КОНСУЛЬТАНТ:

 419000110

 

Способы оплаты
Оплата наличнымиПо безналичному расчёту
Сервисный центр

В нашей компании действует сертифицированный сервисный центр.

Диагностика техники осуществляется бесплатно

Выезд мастера в день обращения

Переводы строк воспринимать как: одинарный перевод строки (из

Ремонт оргтехники

Коды ошибок OKI

коды ошибок
 
  Oki
   OKI 10i    OKI 12i            
                 
                 
 
Индикация Возможная причина
OKIPAGE 10i НАЗАД
ERROR On
aaaaaaaa
An error occurred in the controller.
n= Exception Code
aaaaaaaa= Error Address
Code (nn) Error
1~3
D~F
Reserved
4 Address Error Exception (Load command, command fetch)
5 Address Error Exception (Store command)
6 Bus Error Exception (Command fetch)
7 Bus Error Exception (Load command, store command)
8 System Call Extension
9 Break Point Exception
A Reserved Instruction Exception
B Coprocessor Unusable Exception
C Arithmetic Overflow Exception
ERROR nn An error occurred in the controller.
Code (nn) Error
On A failure occurred in the controller.
n = Exception Code
10 An error was detected by program ROM check.
20 An error was detected by font ROM check.
30 An error was detected by resident RAM check.
40 An error was detected by EEPROM check.
50 An error was detected by optional software ROM check.
52 PS only can't happen.
53 PS only undefined sys call.
60 An error was detected by optional RAM check.
70 A failure occurred with the Fan motor.
71 A failure occurred with the fuser (timeout etc.).
72 A failure occurred with the fuser (thermistor error).
73 A failure occurred with the fuser (thermistor error).
74 SSIO Error
77 A toner sensor fault has occurred when
TOTAL DRAM COUNT is 30 or less.
80 I/F timeout occurred between the main control
board and the operator panel.
81 I/F timeout occurred between the main control board and the optional tray (High Capacity Second Paper Feeder, Power Envelope Feeder, etc.).
90 A watchdog timer timeout occurred.
91 CPU Error
F0 Monitor error (double weight)
F1 Monitor error (argument error)
F2 Optional Timeout error
F3 Optional status error
F4 BG program error
F5 System timer program error.
Defect in the cable of the front feeder paper sensor and the 2-pin connector on the main control board. Poor connection of connectors.
F6 IPT2 program error
F7 IPT1 program error
HOST I/F
ERROR
An error occurred in the serial I/F or network I/F.
This message is displayed when a parity error, a framing error or an overrun error is detected. (When an error occurred in serial I/F)
COVER
OPEN
The upper cover was opened.
COVER T2
OPEN
The High Capacity Second Paper Feeder option cover was opened.
tray
INPUTJAM
A jam occurred during paper hopping from the tray.
tray : TRAY1, TRAY2, FEEDER, MANUAL
tray
FEED JAM
A jam occurred during paper feeding after completion of paper hopping from the tray.
tray : TRAY1, TRAY2, FEEDER
tray
EXIT JAM
A jam occurred during paper ejecting.
tray : TRAY1, TRAY2, FEEDER, MANUAL
tray
SIZE ERR
Paper of improper size is being fed from the tray.
tray : TRAY1, TRAY2, FEEDER, MANUAL
tray
PAPEROUT
The tray has run out of paper.
tray : TRAY1, TRAY2, FEEDER
tray
#REQUEST
Loading of paper indicated by the first line message is requested. The paper size may be one of the followings:
tray : TRAY1, TRAY2, FEEDER
Paper : LETTER, EXECUTIV, LEGAL 14, LEGAL 13, A4 SIZE, A5 SIZE, A6 SIZE, B5 SIZE, COM-9, COM -10, MONARCH, DL ENV, C5 ENV
MANUAL
#REQUEST
Manual loading of paper indicated by the first line message is requested. The paper size one of the followings:
LETTER, EXECUTIV, LEGAL 14, LEGAL 13, A4 SIZE, A5 SIZE, A6 SIZE, B5 SIZE, FREE SIZE, COM-10, MONARCH, DL ENV, C5 ENV
REC BUFF
OVERFLOW
The receive buffer is overflowing.
MEMORY
OVERFLOW
The page buffer is overflowing because it received too much data for printing on the page.
Macro buffer is overflowing.The DLL buffer is overflowing
PRINT
OVERRUN
The printer overrun because the print data is too complicated to be printed.
OFF-LINE
emulate
The printer is in the off-line mode. The second line indicates the emulation.
emulate : AUTO, PCL, PPR, FX, AdobePS, HEX
ACTIVE The printer is processing data.
WAITING
(PS Only)
PostScript mode only. The printer is in the middle of a job and waiting for data to be processed.
PRINTING The printer is printing a page.
DATA
emulate
The printer is processing data in the on-line mode.
Ready ON : The data that is not printed remains in the buffer.
Ready flashing :The printer is receiving data or in printing process.
emulate : AUTO, PCL, PPR, FX, AdobePS, HEX
PRINT
FONTS
All fonts of the printer are being printed during self-test.
PRINT
MENU
The current menu setting is being printed.
Ready ON : Executed by command entry.
Ready flashing : Executed by key operation.
###### Message displayed when the power is turned on. When the power is turned on, the LEDs are turned on for approximately 1 second, conducting a test to verify the conditions of the LEDs and LCD.
INITIALIZING Message displayed to indicate that the controller is undergoing an initialization when the power is turned on.
This message is displayed after the turning on of the LEDs as described above.
RESET
TO SAVE
Message displayed to indicate that in order to reflect the changes in the menu to the editing environment, RESET must be executed. This message is displayed when the printer is unable to conduct automatic reset due to the existence of temporary attributes such as DLL/Macro/User Pattern/User Symbol Set.
FMLOADING Indicates in Cold mode due to downloading to flash memory.
FM ERROR Indicates that an error occurs during downloading to flash memory or deleting.
PRINT
DEMO
The demo page is being printed.
Ready LED on : Executed by command entry.
Ready LED blinking : Executed by key operation.
nnn/mmm When the number of copies being printed is two or more, the number of copies being printed is displayed. This massage is displayed together with another message on the first line.
nnn : Current page
mmm : Total page
PR BUSY
(PS Only)
PostScript mode only.
This message is displayed when ON LINE key is pressed while the printer is processing a job, if the JOB RESET in menu is off. The printer goes off-line after completing the job.
PRINT
CLEANING
This message is displayed when the printer is performing the cleaning print.
CLEANING
MANUAL#
Manual loading of paper indicated by the second line message is being reequested for cleaning. The paper size(#) may be one of the following:
# : LETTER REQUEST, A4 SIZE REQUEST
RESET
TO FLUSH
(PS Only)
PostScript mode only.
This message is displayed when ON LINE key is pressed while the printer is processing a job, if the JOB RESET in menu is on. Even while this message is being displayed, the printer continues to process the job normally.
FLUSHING
(PS Only)
PostScript mode only.
This message is displayed during cancelling of a job. The message goes off when the job cancellation is completed.
RESET The data which remained unprinted in the buffer is deleted and the printer is initialized to user default settings. The temporary DLLs, macros and user pattern are deleted.
RESET
TO SAVE
This message is displayed when the printer cannot reset automatically to exit from the menu because there are date and DLL's and macros having temporary attributes when the printer is changed from set mode to another mode.
TONERLOW Toner is running out.
This message is displayed together with another message on the first line.
Normal operation can be continued.
TONERSNS A fault occurred with the toner sensor.
This message is displayed together with another message on the first line.
Normal operation can be continued.
TONEREMP Displays that the amount of toner is near empty (this status will appear after 100 sheets from a TONER LOW indication).
It is indicated by being combined with other messages in the first line.
Normal operation can be continued.
TONEREMP
CHG CART
Displays that the amount of toner is near empty.
After 100 sheets from a TONER LOW indication, this status will appear and the printing be stopped.
If pressing ON-LINE SW, other 31 sheets can be printed and stopped. And from the next time on, the printing is stopped each sheet.
CHG DRUM This message is displayed together with another message on the first line.
Normal operation can be continued.
NO PS Unavailable printer language was designated by PJL command (warning).
PWR SAVE The printer is in the power-saving mode.
This message is displayed together with another message on the first line.
ERROR PS
AdobePS
(PS Only)
PostScript mode only.
This message appears when the interpreter detects an error while a job is being processed. The remainder of the job is ignored.
OKIPAGE 12i НАЗАД
ERROR On
aaaaaaaa
An error occurred in the controller.
n= Exception Code
aaaaaaaa= Error Address
Code (nn) Error
1~3
D~F
Reserved
4 Address Error Exception (Load command, command fetch)
5 Address Error Exception (Store command)
6 Bus Error Exception (Command fetch)
7 Bus Error Exception (Load command, store command)
8 System Call Extension
9 Break Point Exception
A Reserved Instruction Exception
B Coprocessor Unusable Exception
C Arithmetic Overflow Exception
ERROR nn An error occurred in the controller.
Code (nn) Error
On A failure occurred in the controller.
n = Exception Code
10 An error was detected by program ROM check.
20 An error was detected by font ROM check.
30 An error was detected by resident RAM check.
40 An error was detected by EEPROM check.
50 An error was detected by optional software ROM check.
51 An error was detected by Flash SIMM.
52 PS only can't happen.
53 PS only undefined sys call.
60 An error was detected by optional RAM check.
61 Data bus Error between Cas and Data bus foroption DRAMs.
70 A failure occurred with the Fan motor.
71 A failure occurred with the fuser (timeout etc.).
72 A failure occurred with the fuser (thermistor error).
73 A failure occurred with the fuser (thermistor error).
74 SSIO Error
77 A toner sensor fault has occurred when
TOTAL DRAM COUNT is 30 or less.
79 LED Head type Error
80 I/F timeout occurred between the main control
board and the operator panel.
81 I/F timeout occurred between the main control board and the optional tray (High Capacity Second Paper Feeder, Power Envelope Feeder, etc.).
90 A watchdog timer timeout occurred.
91 CPU Error
F0 Monitor error (double weight)
F1 Monitor error (argument error)
F2 Optional Timeout error
F3 Optional status error
F4 BG program error
F5 System timer program error.
Defect in the cable of the front feeder paper sensor and the 2-pin connector on the main control board.
Poor connection of connectors.
F6 IPT2 program error
F7 IPT1 program error
HOST I/F
ERROR
An error occurred in the serial I/F or network I/F.
This message is displayed when a parity error, a framing error or an overrun error is detected. (When an error occurred in serial I/F)
COVER
OPEN
The upper cover was opened.
COVER T2
OPEN
The High Capacity Second Paper Feeder option cover was opened.
tray
INPUTJAM
A jam occurred during paper hopping from the tray.
tray : TRAY1, TRAY2, FEEDER, MANUAL
tray
FEED JAM
A jam occurred during paper feeding after completion of paper hopping from the tray.
tray : TRAY1, TRAY2, FEEDER
tray
EXIT JAM
A jam occurred during paper ejecting.
tray : TRAY1, TRAY2, FEEDER, MANUAL
tray
SIZE ERR
Paper of improper size is being fed from the tray.
tray : TRAY1, TRAY2, FEEDER, MANUAL
tray
PAPEROUT
The tray has run out of paper.
tray : TRAY1, TRAY2, FEEDER
tray
#PAPER
REQUEST
(The indicate rotate)
Loading of paper indicated by the first line message is requested. The paper size may be one of the followings:
tray : TRAY1, TRAY2, FEEDER
Paper : LETTER, EXECUTIV, LEGAL 14, LEGAL 13, A4 SIZE, A5 SIZE, A6 SIZE, B5 SIZE, COM-9, COM -10, MONARCH, DL ENV, C5 ENV
MANUAL
#REQUEST
Manual loading of paper indicated by the first line message is requested. The paper size one of the followings:
LETTER, EXECUTIV, LEGAL 14, LEGAL 13, A4 SIZE, A5 SIZE, A6 SIZE, B5 SIZE, FREE SIZE, COM-10, MONARCH, DL ENV, C5 ENV
REC BUFF
OVERFLOW
The receive buffer is overflowing.
MEMORY
OVERFLOW
The page buffer is overflowing because it received too much data for printing on the page.
Macro buffer is overflowing.The DLL buffer is overflowing
OFF-LINE
emulate
The printer is in the off-line mode. The second line indicates the emulation.
emulate : AUTO, PCL, PPR, FX, AdobePS, HEX
ACTIVE
emulate
The printer is processing data.
PRINTING The printer is printing a page.
DATA
emulate
The printer is processing data in the on-line mode.
Ready ON : The data that is not printed remains in the buffer.
Ready flashing :The printer is receiving data or in printing process.
emulate : AUTO, PCL, PPR, FX, AdobePS, HEX
PRINT
FONTS
All fonts of the printer are being printed during self-test.
PRINT
MENU
The current menu setting is being printed.
Ready ON : Executed by command entry.
Ready flashing : Executed by key operation.
###### Message displayed when the power is turned on. When the power is turned on, the LEDs are turned on for approximately 1 second, conducting a test to verify the conditions of the LEDs and LCD.
INITIALIZING Message displayed to indicate that the controller is undergoing an initialization when the power is turned on.
This message is displayed after the turning on of the LEDs as described above.
FMLOADING Indicates in Cold mode due to downloading to flash memory.
FM ERROR Indicates that an error occurs during downloading to flash memory or deleting.
PRINT
DEMO
The demo page is being printed.
Ready LED on : Executed by command entry.
Ready LED blinking : Executed by key operation.
nnn/mmm When the number of copies being printed is two or more, the number of copies being printed is displayed. This massage is displayed together with another message on the first line.
nnn : Current page
mmm : Total page
PRINT
CLEANING
This message is displayed when the printer is performing the cleaning print.
CLEANING
MANUAL#
Manual loading of paper indicated by the second line message is being reequested for cleaning. The paper size(#) may be one of the following:
# : LETTER REQUEST, A4 SIZE REQUEST
FLUSHING
(PS Only)
PostScript mode only.
This message is displayed during cancelling of a job. The message goes off when the job cancellation is completed.
RESET The data which remained unprinted in the buffer is deleted and the printer is initialized to user default settings. The temporary DLLs, macros and user pattern are deleted.
RESET
TO SAVE
This message is displayed when the printer cannot reset automatically to exit from the menu because there are date and DLL's and macros having temporary attributes when the printer is changed from set mode to another mode.
TONERLOW Toner is running out.
This message is displayed together with another message on the first line.
Normal operation can be continued.
TONERSNS A fault occurred with the toner sensor.
This message is displayed together with another message on the first line.
Normal operation can be continued.
TONEREMP Displays that the amount of toner is near empty (this status will appear after 100 sheets from a TONER LOW indication).
It is indicated by being combined with other messages in the first line.
Normal operation can be continued.
TONEREMP
CHG CART
Displays that the amount of toner is near empty.
After 100 sheets from a TONER LOW indication, this status will appear and the printing be stopped.
If pressing ON-LINE SW, other 31 sheets can be printed and stopped. And from the next time on, the printing is stopped each sheet.
CHG DRUM This message is displayed together with another message on the first line.
Normal operation can be continued.
NO PS Unavailable printer language was designated by PJL command (warning).
PWR SAVE The printer is in the power-saving mode.
This message is displayed together with another message on the first line.
ERROR PS
AdobePS
(PS Only)
PostScript mode only.
This message appears when the interpreter detects an error while a job is being processed. The remainder of the job is ignored.
CHG DRUM Informs drum life end. It can be temporarily released by opening and closing the cover or pressing the “ON LINE” switch, but basically, the drum must be replaced.
EEPROM
RESET'NG
Indicates an error from the result of checking EEPROM ID No. The printer will display this for a few seconds and reset the EEPROM to the factory default for a continuous operation. It will occur with a new EEPROM.
ROM-SIMM
ERROR
Reformat error including CPCMCIA header of ROM-SIMM and byte sum.
It will be displayed for 2 seconds at power-on or just before a shift to ON LINE.
Начало | О нас | Контакты | Доставка Copyright © GROUP-CIT 2005-2017
Rambler's Top100
џндекс.Њетрика